Standard Trims
Need a custom size or profile not listed here? We are a custom sheet metal fabrication shop here in Winnipeg that can make any custom trim you need. Call us at 204-254-2494 or email sales@metaldepotltd.com — all trims can be made to your specifications.
Roofing Trims (11)
Ceiling to Wall Trim
Girth: 5.25″Transitions between ceiling and wall surfaces at interior metal-clad junctions.
Drip Edge Trim
Girth: 3.875″Standard eave drip edge directing water off the roof and away from the fascia.
Gable Trim
Girth: 8.5″Covers the rake edge at the gable end, sealing panel edges along the roofline.
Gable (Standing Seam OH) Trim
Girth: 9.5″Gable rake trim profiled to overhang and cap standing seam panel edges.
Hip Cap Trim
Girth: 12″Caps the hip ridge where two sloped roof planes meet at an external angle.
Ridge Cap Trim
Girth: 14″Caps the peak ridge where two roof planes meet. Weathertight seal at the highest point of the roof.
Shanty Cap Trim
Girth: 11″Simple ridge cap for agricultural and outbuilding applications — sheds, barns, farm structures.
Valley Trim
Girth: 24″Installed where two sloping roof planes intersect to direct water down the valley.
Valley (W) Trim
Girth: 24″W-shaped valley trim with centre rib that separates water flows from adjoining roof planes.
Snowguard Trim
Girth: 9″Installed near the eave to slow sliding snow and ice, protecting people and property below.
Transition Trim
Girth: 3.875″Bridges two different panel profiles or roof sections, maintaining a weathertight seal.
Eave & Gutter (7)
Cleat Trim
Girth: 4.5″Provides a hidden fastening point along eave edges to lock panel feet in place.
Gutter Eave Trim
Girth: 6″Eave trim that integrates with a gutter system, directing panel runoff into the eavestrough.
Gutter Eave (Standing Seam)
Girth: 8″Eave-to-gutter transition trim profiled for standing seam panels.
Residential Trough
Girth: 19.125″Standard residential eavestrough. Collects and channels roof runoff to downpipes.
Commercial Trough
Girth: 18.126″Heavy-duty eavestrough for commercial and industrial high-volume water runoff.
Closed Downpipe
Girth: 21.25″Fully enclosed rectangular downpipe for commercial eavestroughs. Clean finished appearance.
Open Downpipe
Girth: 18″Three-sided open-face downpipe for agricultural and commercial wall-mounted applications.
Wall & Fascia Trims (8)
Endwall Trim
Girth: 12″Seals where a sloped roof meets a vertical wall at the endwall junction.
Endwall (Stucco) Trim
Girth: 11.5″Endwall flashing for stucco-clad walls. Weathertight seal at roof-to-stucco connection.
Sidewall Trim
Girth: 12″Flashing where a sloped roof meets a vertical sidewall running parallel to the slope.
Sidewall (Stucco) Trim
Girth: 11″Sidewall flashing for stucco-finished walls at roof-to-stucco junctions.
Facia Trim
Girth: 8″Covers the fascia board at the eave. Protects rafter tails from moisture.
Parapet Trim
Girth: 12″Caps parapet walls on flat or low-slope roofs to prevent water pooling on top of the wall.
Rat Guard Trim
Girth: 4.375″Installed at the base of wall panels at grade level to prevent rodent entry behind cladding.
Window Sill Trim
Girth: 7″Installed at the base of window openings to shed water away from the rough opening.
Corner & Angle Trims (6)
Inside Angle Trim
Girth: 5″Simple L-shaped trim for inside corners where two wall panels meet at a 90° internal angle.
Inside Corner Trim
Girth: 12″Finished inside corner trim with weathertight seal at interior wall junctions.
Inside Corner with Pockets
Girth: 16.5″Inside corner with integrated pockets that receive panel edges for a concealed connection.
Outside Angle Trim
Girth: 5″Simple L-shaped trim for external corners where two wall panels meet at a 90° outside angle.
Outside Corner Trim
Girth: 12″Finished exterior corner trim protecting against water infiltration at outside wall corners.
Outside Corner with Pockets
Girth: 16.5″Outside corner with integrated pockets that capture panel edges for a flush, concealed connection.
Panel Edge & Channel Trims (7)
J Back
Girth: 4.875″Back component of the two-piece J-trim system. Fastens first; J Front snaps over to hide fasteners.
J Front
Girth: 2.25″Snap-on face of the two-piece J-trim system. Clips over the J Back for a fastener-free finish.
J Channel
Girth: 4.25″Standard J-channel that receives panel edges at windows, doors, and wall terminations.
J Track
Girth: 3.75″Panel receiver at edges and transitions, similar to J Channel with a slightly different leg profile.
Z Bar Trim
Girth: 6″Z-shaped flashing used at horizontal siding overlaps, window heads, and horizontal transitions.
Hat Channel Trim
Girth: 12″Structural hat-shaped channel used as a furring member to attach cladding to walls and soffits.
Double Side Drip
Girth: 12.25″Drip edge with returns on both sides where panel edges are exposed on two faces.
Specialty (1)
Louvers
Custom sizes on requestVentilation louvers in custom sizes upon request. Attic vents, wall vents, equipment screening.